Tank Cleaner Super S

 Used as a tank cleaner or for general degreasing, cleaning and gs freeing for double bottom tanks, wing tanks, pipe lines, fuel oil tanks, etc.
 

Tank Lining –     Stainless / Zinc / Epoxy / Phenolic.

• Fuel oil tanks
• Heavy fuel oil storage tanks
• Double-bottom tanks
• Wing tanks
• Deep tanks
• Cargo tanks, subject to cargo compatibility
• Tank pipelines
• Bilges
• Fuel handling systems
• Petroleum-contaminated equipment
• Machinery and metal components
• Heavy oil and grease contaminated surfaces
• Old sludge and hydrocarbon deposits

Tank Cleaner HD is powerful Solvent based Emulsifier, Effectively CLEANS oily greasy mud, Effectively works on Black Oil, Furnace Carbon deposited mess. RXSOL TANK CLEANER HD is blended with new generation penetrating solvent and Emulsifier to make cleaning easy and fast.

Direction to follow to achieve heavy duty TANK CLEANING for heavy fuel oil, sludge, oil, grease, wax, and paraffin removal:

1. Pre-Cleaning / Preparation

• Where operationally possible, remove free oil and pumpable sludge before chemical cleaning.

• Pre-wash the tank using warm or hot high-pressure water to remove loose contamination and expose the heavier deposits to the chemical treatment. The supplied reference similarly recommends high-pressure warm-water prewashing before application.

• Removing loose material before chemical treatment considerably improves chemical efficiency and reduces consumption.

2. Recirculation Method

• Prepare the required cleaning solution according to the severity of contamination.

• As a general starting point:

• Minimum concentration: approximately 0.5%

• For severe contamination, a stronger concentration may be required following an onboard trial.

• Circulate the cleaning solution through the tank, pipelines and associated equipment so that all contaminated surfaces receive adequate contact.

• Heating considerably improves the removal of heavy fuel oils, aged hydrocarbons and sludge.

• For difficult contamination, temperatures approaching 70°C can substantially improve cleaning performance where the tank construction, coating, cargo history and operating conditions permit.

• The reference TDS likewise specifies a minimum 0.5% solution for recirculation and reports best performance around 70°C.

• After cleaning, drain the contaminated solution and rinse thoroughly with fresh water or seawater as appropriate.

3. Rock-and-Roll Method

This method is particularly suitable for tank cleaning while the vessel is underway.

• 0.5-1.0 litre RXSOL Tank Cleaner Super S per 1,000 litres of water.
• Allow the solution to remain in contact with the bottom deposits for approximately 2–6 hours.
• This concentrated initial contact helps penetrate, soften and loosen hardened sludge and petroleum deposits.

• Increase the water level to approximately 30% of tank capacity and allow natural vessel movement to provide agitation.
• Maintain contact for approximately 1–2 days, depending upon contamination and voyage conditions.
• The supplied reference describes the same initial concentration, contact period and 30% filling stage.

• Drain → inspect → rinse → repeat if necessary.

4. Heated Soaking / Ballast Method

• For heavily contaminated fuel-oil tanks, determine the required amount of RXSOL Tank Cleaner Super S and introduce it into the tank.
• Fill the tank to approximately 75% capacity with water and provide heating where possible.
• For severe deposits, maintaining the cleaning emulsion at approximately 60°C for an extended contact period can substantially improve penetration and sludge removal.
• The reference procedure specifies maintaining the emulsion at approximately 60°C for 3-5 days where possible, followed by deballasting and repeated seawater rinsing until the discharge runs clear.
• For exceptionally heavy contamination, the treatment may need to be repeated.

5. Direct / General Degreasing

• Brushing
• Soaking
• Immersion
• Manual application
• Suitable spraying equipment
• Circulation

Product Properties

Tank Cleaner effectively cleans Oil Residue and Sludge from tanks which is compulsory prior to repair tank.

How RXSOL Tank Cleaner Super S achieves effective TANK CLEANING?

RXSOL Tank Cleaner Super S operates through a combination of four cleaning mechanisms.

1. Solvent Action

The solvent phase penetrates petroleum residues and dissolves or softens:

Fuel oil → grease → hydrocarbon deposits → sludge → oily residues

This reduces adhesion between the contamination and the tank surface.

2. Surface Wetting

The surfactant system lowers interfacial tension, allowing the cleaning solution to penetrate beneath oily films and deposits.

3. Emulsification

Once the oil has been loosened, the emulsifying system disperses it into the water phase.

The resulting cleaning mixture typically develops a milky appearance, indicating formation of an oil/water emulsion.

4. Mechanical Removal

Circulation, heating, tank movement, high-pressure washing or brushing provides the mechanical energy required to detach and transport the loosened contamination.